How to Run a Monero Node on a Raspberry Pi for Maximum Trustlessness
Running a Monero node on a Raspberry Pi is a practical way to participate in the Monero network without relying on a remote node that could log your IP address or serve you false data. A full node downloads, validates, and relays every transaction and block, giving you independent verification of the network state. Using a low-power, inexpensive single-board computer like a Raspberry Pi makes this feasible 24/7 without the electricity cost or noise of a desktop machine.
Why a raspberry pi node increases trustlessness
When you connect to a remote node - even one run by a trusted wallet like Cake Wallet or privacy-coins/monero-10-block-unlock-time-spending/">Monero GUI's default - you are trusting that node to serve you correct blockchain data and not associate your transaction broadcasts with your IP address. A full node eliminates both risks. You become a peer that every other node treats equally. The Monero daemon (monerod) handles peer discovery and blockchain sync entirely on your device.
A Raspberry Pi 4 (4GB or 8GB RAM) or Raspberry Pi 5 is the sweet spot. The Pi 3 and earlier models lack enough RAM and processing power for the initial sync, which takes weeks and risks running out of memory. The Pi 4 and 5 can sync the Monero blockchain in roughly 7 - 14 days on a wired internet connection with a fast microSD card or SSD.
Hardware Requirements
- Raspberry Pi 4 (4GB or 8GB) or Raspberry Pi 5 - 4GB minimum; 8GB recommended if you also run other services.
- MicroSD card (64GB or larger) - Class 10 or UHS-I. This holds the operating system.
- External SSD (500GB or larger) - Monero's blockchain was roughly 180GB as of late 2025 and grows by about 1GB per month. An SSD is essential; a USB flash drive or HDD will be too slow for sync and may wear out.
- USB-to-SATA adapter or USB enclosure for the SSD.
- Power supply - Official Raspberry Pi power adapter (5V, 3A or more).
- Ethernet cable - Wi-Fi works but is slower and less reliable for the initial sync.
- Optional: 5V fan and heatsink - The Pi can throttle under sustained load; cooling helps.
Step-by-Step Setup
1. Install the Operating System
Use Raspberry Pi OS Lite (64-bit, no desktop) to minimize overhead. Write the image to the microSD card using Raspberry Pi Imager or dd. Enable SSH during imaging so you can control the Pi headlessly.
2. Connect and Configure the Pi
Insert the microSD, connect the SSD via USB, attach Ethernet and power. SSH in with default credentials (pi/raspberry). Update the system:
sudo apt update && sudo apt upgrade -y
Set a static IP or configure DHCP reservation on your router so the Pi's address doesn't change.
3. Mount the SSD
Format the SSD as ext4 (or use a filesystem you prefer) and mount it. Create a mount point and add an entry to /etc/fstab so it mounts automatically on boot.
sudo mkdir /mnt/ssd
sudo mount /dev/sda1 /mnt/ssd # adjust device name
4. Install Monero
Download the latest Monero Linux command-line tools from getmonero.org. Extract them and copy the binaries to a directory in your path, or run them from the extracted folder.
wget https://downloads.getmonero.org/cli/linux64
tar -xvf linux64
cd monero-*
sudo cp monerod /usr/local/bin/
5. Configure and Run monerod
Create a data directory on the SSD:
mkdir /mnt/ssd/monero
Start the daemon with flags that reduce memory and disk usage on a Pi:
monerod --data-dir /mnt/ssd/monero --prune-blockchain --out-peers 8 --in-peers 4 --limit-rate 2048
--prune-blockchainstores only 1/8 of the blockchain data, cutting disk usage to about 30GB. Pruned nodes still validate all transactions and serve pruned data to other peers.--out-peers 8and--in-peers 4cap connections to prevent CPU overload.--limit-rate 2048limits bandwidth to 2MB/s, keeping the network interface from saturating.
The initial sync will take 7 - 14 days. Monitor progress with tail -f ~/.bitmonero/monerod.log (or wherever your log file is). Once fully synced, the node uses about 1 - 2W of power.
6. Keep the Node Running After Logout
Use tmux or screen to run monerod in a persistent session. Alternatively, create a systemd service so the node starts automatically on reboot:
sudo nano /etc/systemd/system/monero.service
Contents:
[Unit]
Description=Monero Full Node
After=network.target
[Service]
User=pi
ExecStart=/usr/local/bin/monerod --data-dir /mnt/ssd/monero --prune-blockchain --out-peers 8 --in-peers 4 --limit-rate 2048
Restart=on-failure
[Install]
WantedBy=multi-user.target
Enable and start:
sudo systemctl enable monero.service
sudo systemctl start monero.service
Connecting your wallet to your pi node
Point your Monero wallet (Cake Wallet, Monero GUI, or Monero CLI) to your Pi's local IP address and port 18081. For example, in Monero GUI, set the node to 192.168.1.100:18081 (use your Pi's IP). Ensure your wallet's "Allow local connections" setting is enabled.
For remote access outside your home network, do not expose the RPC port directly to the internet. Use a VPN (WireGuard is lightweight) or SSH tunnel. Exposing monerod's RPC port on the open internet invites scanning and potential abuse.
Limitations and Considerations
- Initial sync is slow - Expect weeks, not hours. The Pi's CPU bottlenecks the verification of ring signatures and block headers.
- Pruned nodes cannot serve full blockchain data to other peers - They serve pruned blocks only. This is fine for your own trustlessness but reduces your contribution to the network's full archival data.
- No mining or staking - Monero does not use proof-of-stake. You cannot stake on a Pi.
- No hardware wallet integration - The Pi runs the node only; your wallet software on another device connects to it. The Pi itself holds no private keys.
Is it worth it?
For someone who wants the maximum trustlessness Monero can offer without running a desktop machine 24/7, a Raspberry Pi node is the most power-efficient path. You sacrifice sync speed and some peer contribution, but you gain full verification and zero reliance on third-party infrastructure. If you cannot tolerate the initial sync time, consider using a remote node temporarily while your Pi syncs in the background - then switch once it catches up.
Not financial advice. holdium.xyz publishes market data and general information about digital assets. Crypto assets are volatile and you can lose everything you put in. Nothing here is a recommendation to buy, sell or hold, and we make no price predictions.
Prices are sourced from third parties and may be delayed or wrong. Verify anything you intend to act on against a primary source.